Sentera uses cookies !
Privacy policy
Logo Sentera
Sentera – your partner in HVAC control solutions
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets
Nice, slim white square enclosure, air inlets

CO2 controller | visible CO2 alert, 24 VDC


Product description

CO2 meter to measure temperature, relative humidity, CO2 (carbon dioxide) and ambient light level. The unique enclosure allows flush mounting or surface mounting. The supply voltage is 24 VDC. The sensor algorithm controls one 0-10 V output based on the measured values. This single output directly controls an EC fan, an AC fan speed controller or a damper actuator. All measurements and the output value are available via Modbus RTU communication. The CO2 sensor element is replaceable. In many applications, the ambient light detection is used to control the ventilation system in function of the occupancy of the room.




Article code FCMFF-R
GTIN 0.540.100.300.621.4
Category Room CO2 sensors
Available
Current stock 0 U.
Next arrival 29/07/2022 - 5 U.
Factory lead time 4 Week(s)
Documents

Additional specifications and description


NDIR sensor technology
People produce CO2 or carbon dioxide while breathing. That makes CO2 concentration a good indicator for the occupancy and activity level in a space. In many applications, CO2 sensors are used as an indicator for the ventilation requirements. This HVAC transmitter offers a clear, visual indication of the CO2 level via the green, yellow and red LED. The green LED indicates that the CO2 level is within range - there is sufficient fresh air supply. When the CO2 level enters the alert range, the yellow LED lights up. Red means: CO2 out of range or insufficient fresh air supply.  The measured temperature, relative humidity, CO2, dew point and ambient light level are available via Modbus RTU. NDIR or Non-dispersive Infrared technology is used to measure the CO2 level. This technology offers a low life-cycle cost and a precise and stable long-term operation.

How to control fresh air supply?
The output of this sensor can control an EC fan, an AC fan speed controller or a damper actuator. The output value varies proportionally in function of the measured temperature, humidity and CO2 concentration. When more fresh air is required, the sensor will increase the fan speed or open the damper.

Easy to connect!
The cage clamp terminal blocks reduce wiring and installation time. They eliminate the need for routine maintenance and guarantee a reliable contact for solid or stranded wires. The supply voltage is 24 VDC. The ground terminals of the power supply (V-) and output (GND) are internally not connected. This means that a 4-wire cable is required to connect this sensor. Most 24 VDC power supplies offer protection against short circuit, overload and overvoltage. A 24 VDC supply voltage increases the safety and reliability of your installation.

Easy to use!
This sensor doesn't require any configuration. Once installed, it is ready to use.  The default settings will do for most applications. If necessary, the settings can be adjusted via Modbus RTU. For example, a different output type can be selected to make it compatible with other devices: 0-10 VDC / 0-20 mA / 0-100 % PWM / Modbus RTU. Also the light intensity of the LEDs for status indication is adjustable. The Modbus register map provides a complete overview of all adjustable settings.
   
Self-calibrating to compensate sensor drift
The ABC logic self-calibrating algorithm is by default enabled. This algorithm is designed to be used in applications where CO2 concentrations will drop to outside ambient conditions (400 ppm) at least one time (15 minutes) in a 7day period, which is typically seen during unoccupied periods. The sensor will reach its operational accuracy after 25 hours of continuous operation at a condition that it was exposed to ambient reference levels of air at 400 ppm ± 10 ppm CO2.

Inset mounting or surface mounting
The enclosure offers an IP30 protection against ingress of dust and moisture. It allows surface or inset mounting. To ensure optimal performance, it should be protected from direct sunlight.

 
video
 

Related articles

Website is not supported on Internet Explorer! Please use Chrome, Firefox, Edge or other browser.